Presented here down the page you'll find a lot of good news with regards to Tools You Need to Install a New Bathtub .
Mounting a bathtub isn't precisely brain surgery, however it does require strong plumbing, carpentry, and occasionally, tiling skills. Changing an old bath tub with a brand-new one is also a reasonably challenging project. If the old tub is easily accessible, the job can relocate rapidly; if you need to open up a wall to eliminate the old bathtub as well as position the new tub, the task is a lot harder. In either instance, the project is within a residence handyman's abilities, although you will certainly need a helper to vacate the old tub and also set in the new one. Make certain you have qualified yourself for the task and also are comfortable trying it. As opposed to working with a contractor to take control of a halfway-completed job, it is better to take into consideration using one prior to you start. Possibilities are you might need a professional plumber to make tube links.
This write-up will aid you set up a brand-new bathtub in your shower room if you have actually already acquired a new tub and do not require to change the arrangement of your previous water supply pipelines.
Your devices as well as material checklist need to consist of the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you should do is separate the supply of water. After doing so, turn on the taps to drain pipes any type of water staying in the system. The procedure of eliminating the existing faucets can be rather troublesome because of the limited accessibility that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the remaining water that will certainly come from the pipes. When the supply pipes have actually been gotten rid of, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this process. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old securing substance.
Before carrying on to fit the brand-new faucets, contrast the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a connection to the current supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin making sure that the washers remain in area in between the faucet as well as the sink. Safeguard the tap in position with the supplier supplied backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular faucet ports. The former type ought to be linked to the faucet ends first, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bathtub
Utilizing the two wood boards under its feet, place the bathtub in the called for position. The wooden boards are handy in uniformly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four little points.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the level and readjusting the feet on the bath tub up until the level reads degree.
To install taps, fit the bottom of the outermost adaptable tap port to the ideal supply pipe by making a compression join; then do the same for the various other faucet.
Switch on the water and examine all joints and new pipework for leakages as well as tighten them if essential. Fill the tub as well as also check the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, deal with the bathroom paneling as explained in the producer's user's manual. Tiling and also sealing around the tub needs to wait until the bathtub has been utilized a minimum of once as this will certainly resolve it into its final setting.
Preparing for the Installation
First of all, the supporting structure provided with the bath must be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to make certain that if the faucet includes a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps system to stop strain on the bath tub.
Fit the flexible faucet connectors to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of all of the supplied washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be suited its last placement.
Tiling Around the Bathtub
In the location where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to fracture a rigid seal, triggering the water to permeate the wall in between the bathroom and the tiling, bring about problems with dampness as well as possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of drenched newspaper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to enable the motion experienced when the tub is in usage. The sealer can split rather very early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise quickly offered on the marketplace. It is suggested to fit the floor tiles utilizing waterproof or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very serious about Installing A Bathtub and I am praying you enjoyed reading our post. Liked our blog entry? Please share it. Help another person discover it. I appreciate reading our article about Tools You Need to Install a New Bathtub .
Leading emergency plumbing services available.